Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

厚膜永磁阵列微致动器的磁路研究

研究了厚膜永磁阵列微致动器中的磁场分布，并研究了永磁阵列单元几何尺寸对微致动器电磁力的影响。结果表明，厚膜永磁阵列单元高宽比和磁体单元间隔对微致动器电磁力影响较大磁徕单元高宽比为0．7是一个比较合适的尺寸。     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

单相开关磁阻电机及其控制

通过分析一种可以实现自启动的新型结构的永磁单相开关磁阻电机的基本工作原理，提出了一种性价比较高的控制方案，通过实验得出了结论。     

HT-7U纵场磁体的真空压力浸渍

主要通过模拟匝间流动试验、短样试验和长样试验等 ,探求低温超导托卡马克HT 7U中纵场磁体线圈的绝缘层真空压力浸渍的工艺参数 ,确定工艺流程 ,并以模型线圈试验的电性能和液氦温度下的力学性能来验证工艺参数及工艺流程的可靠性。     

NdFeB永磁靶材溅射模拟

运用SRIM2006软件对Nd2Fe14B靶溅射过程进行了模拟,并就入射离子的入射能量和角度进行了分析,得到溅射产额与入射离子能量、入射角度以及溅射靶材的一般规律:1)溅射产额随着入射离子能量的增加而增加,在低能量区域增加很快,到了高能量区域增加变缓;2)溅射产额随着入射离子入射角度的增大逐渐增大,且在70°~80°出现极大值,如当入射离子的入射角度为75°,入射离子能量为7 keV时,溅射产额可达4.398(原子.离子–1);3)溅射原子的摩尔比与靶材原子摩尔比存在一定偏差,导致薄膜成分与靶材成分不一致。     

注射成形粘结NdFeB磁体:工艺·性能·应用

综合介绍了几种适于注射成形粘结NdFeB磁体的磁粉制备方法及特点；讨论了粘结剂、改性剂及磁场取向对注射成形NdFeB磁体最终磁性能的影响及其应用市场。在此基础上，指出了今后开展研究工作的方向。     

Fe73.5Cu1Nb3Si13.5B9非晶合金的晶化动力学

用ＤＴＡ结合ＸＲＤ了Ｆｅ７３．５Ｃｕ１Ｎｂ３Ｓｉ１３．５Ｂ９晶合金的晶化动力学。表明，该事金在５００℃时析出α－Ｆｅ（Ｓｉ）相。晶化初期激活能最小为２４２ｋＪ／ｍｏｌ，它随晶化量的增加，在ＸＣ为０．４－０．８时，呈极大值为５２０ｋＪ／ｍｏｌ。在６２４℃时析出Ｆｅ２Ｂ相。